Difference between revisions of "NG 900/9-3 Valve Cover Gasket"
| (One intermediate revision by the same user not shown) | |||
| Line 24: | Line 24: | ||
====Ignition Module (IDM or DIC)==== | ====Ignition Module (IDM or DIC)==== | ||
The plastic cover over the intake manifold and the Ignition Module have to be removed first. The ignition module (IDM, a.k.a. the DIC) is held in place by T30 screws and an electrical connector. | The plastic cover over the intake manifold and the Ignition Module have to be removed first. The ignition module (IDM, a.k.a. the DIC) is held in place by T30 screws and an electrical connector. | ||
| + | [[file:900_9-3_VC_1.jpg|thumbnail|none|Fig. 1 - Ignition Module (IDM or DIC)]] | ||
====Other Components==== | ====Other Components==== | ||
| Line 31: | Line 32: | ||
* PCV pipe screw, T-30 torx | * PCV pipe screw, T-30 torx | ||
* Oil filler tube bracket, 10-mm hex bolts | * Oil filler tube bracket, 10-mm hex bolts | ||
| + | [[file:900_9-3_VC_3.jpg|thumbnail|none|Fig. 2 - Other Components]] | ||
===Removal=== | ===Removal=== | ||
====Valve Cover Bolts==== | ====Valve Cover Bolts==== | ||
The valve cover is attached by 16 T-40 torx bolts. Eleven bolts on the outside of the valve cover, and five on the inside. The bolts are fairly tight, and have to be removed using a small ratchet with a short extension and a T-40 bit holder. Clearance for the bit holder is tight near the PCV pipe and the oil filler tube. | The valve cover is attached by 16 T-40 torx bolts. Eleven bolts on the outside of the valve cover, and five on the inside. The bolts are fairly tight, and have to be removed using a small ratchet with a short extension and a T-40 bit holder. Clearance for the bit holder is tight near the PCV pipe and the oil filler tube. | ||
| + | [[file:900_9-3_VC_4.jpg|thumbnail|none|Fig. 3 - Valve Cover]] | ||
====Valve Cover==== | ====Valve Cover==== | ||
The old gasket usually sticks to both the valve cover and the head. It may take a tap with a rubber mallet to break the seal, and some careful prying with a screwdriver before the valve cover comes loose, and can be lifted off. The top of the engine, timing chain, timing gears etc. can now be inspected. | The old gasket usually sticks to both the valve cover and the head. It may take a tap with a rubber mallet to break the seal, and some careful prying with a screwdriver before the valve cover comes loose, and can be lifted off. The top of the engine, timing chain, timing gears etc. can now be inspected. | ||
| + | [[file:900_9-3_VC_5.jpg|thumbnail|none|Fig. 4 - Valves]] | ||
===Assembly=== | ===Assembly=== | ||
====Gasket Replacement==== | ====Gasket Replacement==== | ||
The valve cover groove should be cleaned and dried before inserting a new gasket. It can be coated with a few dabs of tacky grease or gasket sealer/dressing to help hold the gasket in place when the cover is turned over for assembly. The surface at the head where the valve cover will be seated should also be clean and dry before reassembly. | The valve cover groove should be cleaned and dried before inserting a new gasket. It can be coated with a few dabs of tacky grease or gasket sealer/dressing to help hold the gasket in place when the cover is turned over for assembly. The surface at the head where the valve cover will be seated should also be clean and dry before reassembly. | ||
| + | [[file:900_9-3_VC_6.jpg|thumbnail|none|Fig. 6 - Valve Cover Gaskets]] | ||
====Gasket Sealer==== | ====Gasket Sealer==== | ||
Sometimes a new gasket is not engough to stop the leaks. In that case, small amounts of silicone gasket sealer may have to be used in areas where the cover leaks, like the half-moon seals which close off openings in the block. Otherwise some tacky grease or gasket dressing is sufficient. | Sometimes a new gasket is not engough to stop the leaks. In that case, small amounts of silicone gasket sealer may have to be used in areas where the cover leaks, like the half-moon seals which close off openings in the block. Otherwise some tacky grease or gasket dressing is sufficient. | ||
| + | [[file:900_9-3_VC_7.jpg|thumbnail|none|Fig. 7 - "Half-moon" seals to be filled with Gasket Sealer]] | ||
====Valve Cover Plug==== | ====Valve Cover Plug==== | ||
If the plug was also leaking, it can be replaced or sealed with Permatex sealer, as shown on the left. For more details on the plug: | If the plug was also leaking, it can be replaced or sealed with Permatex sealer, as shown on the left. For more details on the plug: | ||
| + | [[file:900_9-3_VC_9.jpg|thumbnail|none|Fig. 8 - Valve Cover Plug]] | ||
[[900/9-3 Valve Cover Plug Repair|Valve Cover Plug Repair]] | [[900/9-3 Valve Cover Plug Repair|Valve Cover Plug Repair]] | ||
====Valve Cover==== | ====Valve Cover==== | ||
The valve cover is turned over carefully with the gasket in place and replaced on the engine. Use two bolts to locate the cover in the correct position. Next check the position of the half-moon seals. Finally, tighten valve cover bolts to about 11 lb-ft, in the sequence shown at left. | The valve cover is turned over carefully with the gasket in place and replaced on the engine. Use two bolts to locate the cover in the correct position. Next check the position of the half-moon seals. Finally, tighten valve cover bolts to about 11 lb-ft, in the sequence shown at left. | ||
| + | [[file:900_9-3_VC_8.gif|thumbnail|none|Fig. 9 - Valve Cover Bolt Tightening Sequence]] | ||
====Remaining Parts==== | ====Remaining Parts==== | ||
Latest revision as of 08:10, 10 August 2010
Contents
Overview
Valve cover leaks are common. Sources include the grommet at the valve cover opening for the PCV system, the valve cover plug at the end of one of cam used for the distributor shaft on non-turbo engines, and the valve cover gasket itself. Most valve cover gaskets lose their elasticity eventually and start to leak. Replacement is fairly straight forward, and a good opportunity to inspect the valve cover for oil deposits which form in many engines by 100k miles.. There are relatively few tools required (T25 and T30 bits, a small ratchet with a bit holder, a new set of gaskets (there is an inner and outer gasket, sold as a kit), and optionally some gasket sealer or gasket "dressing".
Removal and Replacement
Tools
- 3/8 drive ratchet
- T-30 bit or driver (ignition cassette)
- T-40 bit (valve cover bolts)
- 10-mm socket
- Torque wrench (optional)
- Solvent (cleaner)
- Wire brush (valve cover groove)
- Grease or gasket dressing
- Permatex gasket sealer
Torque Wrench Settings
- Ignition cassette, 8 lb-ft
- Valve cover bolts, 11 lb-ft
Parts
- Valve Cover Gasket Kit - p/n 8822041
Access
Ignition Module (IDM or DIC)
The plastic cover over the intake manifold and the Ignition Module have to be removed first. The ignition module (IDM, a.k.a. the DIC) is held in place by T30 screws and an electrical connector.
Other Components
- Air filter box, 10-mm nuts
- Air intake hose, hose clamps
- PCV Nipple, unplug from valve cover
- PCV pipe screw, T-30 torx
- Oil filler tube bracket, 10-mm hex bolts
Removal
Valve Cover Bolts
The valve cover is attached by 16 T-40 torx bolts. Eleven bolts on the outside of the valve cover, and five on the inside. The bolts are fairly tight, and have to be removed using a small ratchet with a short extension and a T-40 bit holder. Clearance for the bit holder is tight near the PCV pipe and the oil filler tube.
Valve Cover
The old gasket usually sticks to both the valve cover and the head. It may take a tap with a rubber mallet to break the seal, and some careful prying with a screwdriver before the valve cover comes loose, and can be lifted off. The top of the engine, timing chain, timing gears etc. can now be inspected.
Assembly
Gasket Replacement
The valve cover groove should be cleaned and dried before inserting a new gasket. It can be coated with a few dabs of tacky grease or gasket sealer/dressing to help hold the gasket in place when the cover is turned over for assembly. The surface at the head where the valve cover will be seated should also be clean and dry before reassembly.
Gasket Sealer
Sometimes a new gasket is not engough to stop the leaks. In that case, small amounts of silicone gasket sealer may have to be used in areas where the cover leaks, like the half-moon seals which close off openings in the block. Otherwise some tacky grease or gasket dressing is sufficient.
Valve Cover Plug
If the plug was also leaking, it can be replaced or sealed with Permatex sealer, as shown on the left. For more details on the plug:
Valve Cover
The valve cover is turned over carefully with the gasket in place and replaced on the engine. Use two bolts to locate the cover in the correct position. Next check the position of the half-moon seals. Finally, tighten valve cover bolts to about 11 lb-ft, in the sequence shown at left.
Remaining Parts
Reassemble in reverse order,
- Oil tube bracket
- PCV pipe
- PCV nipple, clean and insert into the valve cover bushing
- Air box
- Air Intake hose
- Ignition Cassette
